Top 10 typical forklift mishaps ， forklift operation must focus on these matters ！.

Top 10 typical forklift mishaps ， forklift operation must focus on these matters ！.

Blog Article

Do not take too lightly the forklift at the workplace. If the operation is bad, there will be serious mishaps in minutes, and there are many crashes entailing forklifts.

Situation 1: The forklift freight blocked the vehicle driver's view, and the individual in front can not be discovered, resulting in a rolling crash.
Instance 2: In order to maintain the balance of the forklift when lifting hefty items, the employees used their body weight as the counterweight, which practically caused casualties.
Case 3: The width of the forklift freight goes beyond the allowable width of the route and hangs on the roadside rack, which practically causes an crash.
Instance 4: Forklift is speeding and surrender during a turn.
Instance 5: The forklift vehicle driver did not discover the pedestrian, and the pedestrian did not notice the forklift.
Case 6: The forklift raises the employees illegally, the forklift motorist does not put on the safety belt, the forklift lifter drops and the driver is crushed when the forklift surrender.
Case 7: The forklift driver did not use a seat belt and fell from the vehicle when it surrendered and was crushed.
Forklift procedure ought to pay attention to these issues ：.

Begin.
1. Prior to beginning, observe the environments, and after confirming that there are no obstacles that hinder the security of driving, beep the horn initially and then begin.
2. For vehicles with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) scale need to be secure before starting.
3. When the forklift starts with a lots, the vehicle driver should first validate that the lots is stable and reliable.
4. The begin should be sluggish and consistent.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground must be maintained 300mm-400mm, and the mast must be slanted in reverse. .
2. Do not raise the fork expensive when driving. When entering and leaving the work site or while driving, take care that there will be no obstacles in the sky. When the tons is traveling, the fork has to not be raised expensive, which will affect the security of the forklift. .
3. After dumping, the fork should be decreased to the regular driving placement prior to driving. .
4. When turning, if there are pedestrians or lorries close by, the driving signal must be provided initially. High-speed doglegs are prohibited. High-speed doglegs will certainly create the lorry to shed lateral stability and topple. .
5. When the forklift is downhill, it is purely forbidden to shut off the fire and slide, and it is restricted to brake all of a sudden while driving with tons unless there are unique circumstances.
6. When the forklift is running, it should follow the website traffic rules in the manufacturing facility and must keep a certain safety distance from the car in front. .
7. When the forklift is running, the tons needs to remain in the most affordable setting that does not impede the driving, and the gantry must be effectively slanted back. The lots will not be increased other than when stacking or packing. .
8. The height of the load should not block the chauffeur's sight. In unique circumstances, when the thing influences the forward vision, drive at a reduced rate when reversing.
9. It is prohibited to turn on the ramp, nor to drive throughout the ramp. .
10. The secure driving rate of the forklift in the factory area is 5 km/h, and it must drive securely at a reduced speed when entering the production workshop location. .
11. When the forklift is raised, lifted or driven, it is forbidden for employees to depend on the fork to hold products and play a balancing duty. .
12. If troubles are discovered, they will be fixed and reported in a prompt manner, and they will certainly never ever operate with illnesses or hide them.

packing and unloading.
1. When fork-loading things, the range between both forks should be readjusted as required to make the load of both forks balanced and not manipulated, and one side of the product should protest the rack. .
2. It is forbidden to deal with a single fork or make use of a fork top or pull. In unique scenarios, safety indication should be established to remind bordering pedestrians. .
3. In the process of packing and dumping products, the forklift has to be stopped with the brake. .
4. The speed of the car should be slow-moving and stable. Be careful not to roll the wheels on the dunnage, so as not to extend the rolled things and harm individuals. .
5. When utilizing a fork to fork the goods, the fork needs to be as deep as possible under Stand-on Electric Pallet Stacker the lots, and it should be kept in mind that the fork tip must not touch various other products or things. The load must be maintained with very little back tilt Stand-on Electric Pallet Stacker of the gantry to make sure that the load does not move in reverse. The mast can be tilted onward slightly when the tons is decreased to allow for simple positioning of the lots and extraction of the forks. .
6. It is prohibited to fork items at broadband and collide with difficult items with the fork head. .
7. When the forklift is functioning, it is forbidden for people to stand around the fork, so regarding stay clear of the collapse of the goods and hurt people. .
8. Overwhelming is banned, and it is prohibited to use forks to lift workers to take part in high-altitude procedures to stay clear of high-altitude falling accidents. .
9. It is not enabled to use the brake inertia to slide, place, round or roll things. .
10. It is not permitted to make use of forks to pick, turn pallet unload.

Leaving .
1. It is forbidden to leave the forklift when the products on the fork are in the air. Before leaving the forklift, you need to discharge the goods or reduced the fork structure.
2. Draw the hand brake take care of to dead or dispirit the hand brake button.
3. The engine is switched off and the power is removed. (Except for unique conditions, such as the vehicle driver does not leave the lorry's view and does not go beyond 1 min).
4. Get rid of the secret. .

Forklift Operation Precautions.
1. Prior to and after the forklift operation, the appearance should be checked, and gas, lubing oil and air conditioning water must be added.
2. Check the safety performance of beginning, running and stopping.
3. Inspect whether the lights and horn signals are complete and effective.
4. Throughout the procedure of the forklift, inspect whether the pressure and temperature are regular.
5. After the forklift is running, the outside leakage should also be examined and the seals must be replaced in time.

Forklift Safety Operation Specifications.
1. You must examine prior to leaving the automobile;.
2. When you experience someone before you during driving, you should send out a signal at a distance of 5 m;.
3. The driving speed in the factory does not go beyond 5 km/h;.
4. When driving, the low point of the freight must be 0.3 m ~ 0.4 m above the ground;.
5. The transforming must not be too sharp to stop the propensity of "free switching";.
6. Running up and down the incline ought to be slow and consistent, and no turning on the incline is allowed.
7. Do not drive throughout the gradient. When the slope is higher than 10%, the lorry ought to be driven in reverse when declining;.
8. When the forklift personnel bring the goods and move forward, if they come across large or heavy items and go to the vehicle driver's line of vision, they need to take the reversing workout
.
The "Eight Prohibitions" should be complied with in the procedure.
1. Single fork procedure is not allowed.
2. It is not enabled to raise the goods for long distance driving.
3. It is not enabled to grab the goods by turning over the pallet with the fork.
4. It is not permitted to straight shovel chemicals, flammables and other harmful chemicals with forks.
5. It is not permitted to use inertia pressure to grab the goods.
6. It is not allowed to utilize stopping pressure to exile round or easy-to-roll objects.
7. It is not enabled to bring individuals to work on the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is elevated.
8. Do not drive laterally on slopes
.
Car park is not permitted under the following conditions.
1. Curves, slim roadways, train crossings;.
2. Areas with a longitudinal incline higher than 5%.
3. When there is an challenge on one side of the roadway, the contrary side of the area with the very same length as the obstacle ought to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：info2@onen.cn
Phone：+86 13827083844